DeWalt DCT419S1 Instrukcja Użytkowania i Eksploatacji Strona 20
- Strona / 76
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
18
English
MAINTENANCE
Cleaning
WARNING: Blow dirt and dust off with clean, dry air at least once
a week. To minimize the risk of eye injury, always wear ANSI Z87.1
approved eye protection when performing this.
WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals may
weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC
outlet before cleaning. Dirt and grease may be removed from the
exterior of the charger using a cloth or soft non-metallic brush. Do not
use water or any cleaning solutions.
Troubleshooting
SITUATION PROBABLE CAUSE SOLUTION
Unit does not
turn on
• No power to unit • Make sure 12V Max*
battery pack is fully
charged
• Fully seat the 12V Max*
battery pack in the handle
Unit does not
display embedded
materials; says
"Pre-Scan Data
Mapping"
• Unit is in process of
mapping scanned
area
• Review the Scanning
Process section of the
manual
SITUATION PROBABLE CAUSE SOLUTION
Frequently getting
"Lost Contact"
error
• Need to re-initialize • Remove unit from the
wall. When the "Begin
Scanning" screen
appears, press the OK
button (I). Ensure that
the unit is off of the wall
surface and that there is
nothing such as a hand or
other object on the back
surface. Press the OK
button (I) to complete the
initialization process.
No embedded
materials detected
or diffi culty
in detecting
embedded
materials
• Too narrow of area
mapped
• Diffi culty in scanning
below special wall
condition
• Re-map larger area
• Scan slowly
• Scan in a straight line
• Review the Detection
through Special Surface
Conditions section of the
manual
• Scan in both the horizontal
and vertical directions
• Ensure that the unit is
at least 6" (150mm)
away from the wall when
powering on
Diffi culty in
detection of metal
• Metal items too
deep
• Scan in both horizontal
and vertical straight
lines. Metal sensitivity is
increased when the metal
object is parallel to the
sensor. NOTE: The metal
sensing is located at the
bottom of the unit.
- EWALT • www.dewalt.com 1
- Battery Tool Use and Care 4
- Scanners 4
- Conditions 5
- Battery Packs 6
- READ ALL INSTRUCTIONS 6
- Regulatory Notices 6
- The RBRC™ Seal 7
- Battery Chargers 8
- Chargers 9
- Charging Procedure (Fig. 1) 9
- Indicator Light Operation 9
- Charge Indicators 9
- Wall Mounting 10
- Important Charging Notes 10
- Storage Recommendations 10
- SAVE THESE INSTRUCTIONS 11
- FOR FUTURE USE 11
- COMPONENTS (Fig. 2) 11
- Error Messages 16
- Menu Options (Fig. 2) 18
- Operating Tips 19
- MAINTENANCE 20
- Cleaning 20
- Troubleshooting 20
- Accessories 21
- Register Online 22
- Three Year Limited Warranty 22
- EWALT, COMPOSEZ LE NUMÉRO 24
- EWALT (1-800-433-9258) 24
- Français 25
- Utilisation et entretien 25
- LIRE TOUTES LES CONSIGNES 28
- Le sceau SRPRC 29
- Chargeurs 31
- Procédure de charge (Fig.1) 31
- Recommandations de stockage 33
- CONSERVER CES CONSIGNES POUR 33
- UTILISATION ULTÉRIEURE 33
- DESCRIPTION (Fig. 2) 33
- Crochet de ceinture (Fig.3) 34
- (accessoire en option) 34
- UTILISATION 34
- Messages d’erreur 39
- Options menu (Fig. 2) 40
- Conseils d’utilisation 42
- Entretien 42
- Guide de dépannage 42
- Accessoires 45
- Réparations 45
- Registre en ligne 46
- Garantie limitée de trois ans 46
- Notifi caciones regulatorias 52
- LEA TODAS LAS INSTRUCCIONES 52
- El sello RBRC™ 53
- EWALT. Otros tipos 54
- Cargadores 55
- Indicadores de carga 56
- Montaje en la pared 56
- SU FUTURA UTILIZACIÓN 57
- PIEZAS (Fig. 2) 57
- Gancho para cinturón (Fig. 3) 58
- (Accesorio opcional) 58
- OPERACIÓN 59
- Los primeros pasos (Fig. 2) 59
- TIPO DE CONSTRUCCIÓN 61
- Mensajes de error 63
- Opciones del menú (Fig. 2) 65
- Consejos para el uso 66
- MANTENIMIENTO 67
- Limpieza 67
- Resolución de problemas 67
- Accesorios 69
- Reparaciones 70
- Póliza de Garantía 71
- Registro en línea 71
- “HERRAMIENTAS ELECTRICAS” 73
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.228 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji